701 MMA Floor Coating is a two pack, fast curing coating designed to provide a dust-free, seamless floor finish with protective and decorative properties on concrete and steel surfaces. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.
Also available in 4,000+ colour options from RAL, BS and NCS
701 MMA Floor Coating is a two pack, fast curing coating designed to provide a dust-free, seamless floor finish with protective and decorative properties. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.
701 MMA Floor Coating can be trafficked after just 1 hour (see ‘curing’ for full details), allowing a fast return to service and can be applied at temperatures as low as -20°C.
This product is for Professional Use Only.
Recommended Uses:
As a rapid curing, abrasion and chemical resistant floor coating where minimal downtime is paramount
Suitable mechanical treatment, such as vacuum grit blasting, is the preferred treatment prior to application as this ensures a mechanical ‘key’ which will optimise adhesion
Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish Standard
All dust shall be removed prior to coating application. A coat of 707 MMA Metal Primer shall be applied as soon as practicable after blasting, in order to obviate the possible occurrence of ‘flash rusting’
Priming:
Concrete surfaces shall be primed with a coat of 706 MMA Floor Primer, applied by brush or roller, at a nominal rate of 0.3kg/m²
Long nap lambswool rollers are recommended for primer application
Allow primer to cure for a minimum of 40 minutes
Steel surfaces shall be primed with 707 MMA Metal Primer as soon as practicable after blasting
Damp concrete surfaces can be primed using 709 MMA Damp Proof Primer – refer to product data sheet for full details
Mixing:
701 MMA Floor Coating is supplied as a two pack material consisting of the base component, and the catalyst component, incorporate the catalyst component into the base component under mechanical stirring, and mix for 1-2 minutes
Mixing Ratio:
(% Catalyst by Weight) = 1.8
Application
Apply 701 MMA Floor Coating using short nap perlon, or smooth lambswool rollers at a nominal rate of 0.30kg/m²
Following a minimum of 1 hour apply a second coat at the same nominal rate
Should a slip resistant or skid resistant finish be required then broadcast 504 Standard Anti Slip Aggregate onto the first coat within 10 minutes of application
Following a minimum of 1 hour, sweep off excess aggregate and apply a second coat of 701 MMA Floor Coating
Note: 701 MMA Floor Coating may be applied at greater thicknesses should service conditions warrant it.
Cleaning
Clean equipment with 109 Tool Cleaner prior to the curing of the coating
Curing
Light Foot Traffic: 1 hour @ 20°C
Vehicular Traffic: 2 Hours @ 20°C
Full chemical resistance: 24 hours @ 20°C
Limitations
Do not apply to wet, uncured or un-primed concrete surfaces
701 MMA Floor Coating will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Storage & Shelf Life
Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
Adequate ventilation of the storage area should be provided
Keep container tightly closed when not in use
701 MMA Floor Coating has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
701 MMA Floor Coating is flammable during application, so adequate safety precautions should be observed.
Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
701 MMA Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
701 MMA Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased `anti-slip` properties in both dry and wet conditions to improve safety.
Produces a rough, non-skid surface
Hard wearing and chemical resistant
Coloured Quartz Aggregate 0.4-0.8mm...
706 MMA Floor Primer is a rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.
Ideal for use as a rapid curing primer for...
707 MMA Metal Primer is a rapid curing three-pack primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds.
Rapid cure, even at low temperatures - from as low as -30°C*
Very good corrosion resistance
Excellent adhesion
Impervious to water...
709 MMA Damp Proof Primer has been developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds.
Rapid cure, even at low temperatures - from as low as -30°C*
Very good chemical resistance
Excellent adhesion to damp concrete
Impervious to water
Pre-packed units ready for use
Easily...
710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.
Resilient
Very good chemical resistance
Excellent adhesion
Fast curing, even at low temperatures (down to -10°C*)
Impact and abrasion resistant...
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.
Low Hazard
Low evaporation rate
Excellent solvency powers
80% biodegradable
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product
More...