Carboline Carbotherm 3300

8390

Carboline Carbotherm 3300, a ceramic blend insulative composite coating formulated in a high temperature resistant acrylic binder that inhibits heat transfer into or out of a structure. Its insulative properties keeps structures exposed to solar radiation significantly cooler and can be used to minimize or eliminate sweating of pipes or other operating equipment. 

  • Excellent thin-film insulation
  • Unique formula provides superior coverage during application
  • Protects personnel from hot surfaces
  • Multi-purpose interior/exterior coating
  • Insulation provides anti-condensation properties
  • Easy to use - zero VOC; low odour
  • May be applied to hot surfaces
  • Service temperatures range from as low as -51° up to 176°C
  • Dries for recoating in as little as 3 hours (at 24°C)

This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].

Colour
Size
Finish
Quantity
Product not available
This Product is Price on Application Only

100% secure payments
Description

Carboline Carbotherm 3300 is a ceramic blend insulative composite coating formulated in a high temperature resistant acrylic binder.  It also inhibits heat transfer into or out of a structure. Its insulative properties keeps structures exposed to solar radiation significantly cooler. It can be used to minimize or eliminate sweating of pipes or other operating equipment.



Click To Jump To Section:




Features and Benefits


  • Excellent thin-film insulation
  • Unique formula provides superior coverage during application
  • Protects personnel from hot surfaces
  • Multi-purpose interior/exterior coating
  • Insulation provides anti-condensation properties
  • Easy to use
  • Zero VOC; Low odour
  • May be applied to hot surfaces
  • Eggshell finish



Product Specification


Technical Data
Carboline Carbotherm 3300
Volume Solids: 90% +/- 2%
Theoretical Coverage Rate: 35.4 m²/l at 25 microns
2.2 m²/l at 400 microns
1.4 m²/l at 625 microns
Allow for loss in mixing and application
Dry Film Thickness: Number of coats depends on the operating temperature and degree of insulation or protection needed.
Primers: For service temperatures:
Up to 112°C: Use Carbocrylic 3358 Series; Carboguard 553 or Carboguard 890
Up to 149°C: Use Carbozinc 11 Series; Carboguard 690 or Carbomastic 15 Series
Up to 176°C: Use Carbozinc 859
Topcoats: May be topcoated with acrylics for custom colours or gloss
For custom colours or for high humidity/wet exposures use Carbocrylic 3350 or Carbocrylic 3359
Service Temperature: -51°C to 176°C
For initial service avoid sudden temperature "surges". Do not exceed 93°C during the first hour.
VOC Values: As Supplied: 0.00
Flash Point: 93°C
Shelf Life: 24 months at 24°C
Storage Temperature and Humidity: 4°C - 43°C
0-95% Relative Humidity



Performance Data
Test Method System Results
Accelerated Aging/Salt Fog (ASTM B117) Carbozinc 859/Carbotherm 3300/Carbocrylic 3359 DTM 2016 hrs; No blisters or rust on the plane or scribe; Few to medium #2 blisters at scribe
Cyclic QUV-A/Prohesion (ASTM D5894) Carbozinc 859/Carbotherm 3300/Carbocrylic 3359 2016 hrs; No effect, No blisters or rust on plane or scribe
Elongation (ASTM D638) Carbotherm 3300 25%
Emissivity (ASTM E408) Carbotherm 3300 0.88
Flame Spread (ASTM E84) Carbotherm 3300 Flame Spread: 0 Smoke Development: 0
Humidity Cabinet (ASTM D2247) Carbozinc 859/Carbotherm 3300/Carbocrylic 3359 DTM 2016 hrs; No effect, No blister or rust on plane or scribe
R Value Carbotherm 3300 (tested at 0.172") 0.251 hr-ft2-°F/BTU
Solar Reflectivity (ASTM E903) Carbotherm 3300 86.2
Thermal Conductivity @77°F/24°C; (ASTM C177) Carbotherm 3300 (tested at 0.172") 0.0570 BTU/hr-ft-°F (0.0987 W/m-°K)
Thermal Transmittance @77°F (ASTM C177) Carbotherm 3300 (tested at 0.172") 3.98 BTU/hr-ft2-°F



Drying Times


Curing Schedule
Surface Temp Dry to Recoat
16°C 6 Hours
24°C 3 Hours
32°C 1.5 Hours



  • These times are based on a 500 micron dry film thickness. Higher film thicknesses, insufficient ventilation, high humidity, or cooler temperatures will require longer cure times
  • The material is typically ready to recoat when it passes a "dry to handle" test (thumb twist test). If a final color coat (see Topcoats) is used; allow 36-48 hours dry time to ensure complete dryness prior to final colour coat



Surface Preparation


General

  • Surfaces must be clean and dry
  • Employ adequate methods to remove dirt, dust, oil, and all other contaminants that could interfere with adhesion of the coating.

Steel

  • Prime with appropriate primers as recommended in section on "Primers"

Stainless Steel

  • Abrasive blast to a 1-1.5 mil profile and apply appropriate primer



Application Methods


Product Information
Mixing: Separation of coating may occur and is common. Turning containers upside down for an hour just prior to mixing will dramatically facilitate mixing. Use a drywall compound mixing paddle (in reverse) to incorporate material to a homogeneous consistency resembling a milkshake. Normally this will take several minutes. Avoid contact of mixing blade and edge of plastic buckets to avoid shearing plastic pieces into coating. If other types of blades or high-powered mixers are used, avoid high shear or over mixing
Thinning: No thinning is required
Spray Application: Pre-rinse (and lubricate) equipment with undiluted Carboline Surface Cleaner 3 followed by clean potable water before spraying.
Conventional Spray: Bottom outlet pressure pot works best, equipped with dual regulators, ½” I.D. minimum material hose, 0.070” I.D. fluid tip and appropriate air cap. Adjust line air pressure to 40 psi and pot pressure to 15 psi
Airless Spray: Pump Ratio: 30:1 min
Volume Output: 3.0 gpm min
Material Hose: 3/8” I.D. min
Tip Size: .021-.025”
Output PSI: 1800-2200
Filter Size: Remove filters
Brush and Roller: Multiple coats may be required to achieve recommended dry film thickness. Brushing may negatively affect insulative properties; use for touching up of small areas only. Avoid excessive re-brushing
Brush: Use a synthetic bristle brush. Use for touching up of small surface areas only
Roller: Not recommended



Application Conditions


Product Conditions
Condition Material Surface Ambient Humidity
Minimum 10°C 10°C 10°C 0%
Maximum 38°C 149°C 43°C 80%



  • It is best to spray apply a light 5-10 mil coat and allow to tack dry prior to full coating. This is especially helpful over hot surfaces which may require 2-4 light passes between 165-150°C
  • Do not apply when the surface temperature is less than 53°C above the dew point. Do not apply if temperatures are expected to drop below 10°C within 24 hours of application
  • Special application techniques may be required above or below normal application conditions
  • Dry times will be aided by higher temperatures, lower humidity, hotter substrates, and more air movement during application and curing



Health and Safety


Clean Up

  • Use Thinner 2 or Acetone
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

  • Read and follow all caution statements on this product data sheet and on the safety data sheet for this product and use personal protective equipment as directed
  • Hypersensitive persons should wear protective clothing, gloves, and use protective cream on face, hands, and all exposed areas
  • Keep container closed when not in use
Product Details
8390

Data sheet

Manufacturer
Carboline
For Use On
Steel, Stainless Steel
Application Method
Spray, Brush
Sheen
Eggshell
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Single
Pack Size
15L
Coverage
1444 ft²/gal at 1.0 mils (35.4 m²/l at 25 microns) - 90 ft²/gal at 16.0 mils (2.2 m²/l at 400 microns) - 58 ft²/gal at 25.0 mils (1.4 m²/l at 625 microns)
Solids by Volume
90% +/- 2%
Shelf Life (from date of manufacture)
24 months at 24°C
Recommended Dry Film Thickness
Number of coats depends on the operating temperature and degree of insulation or protection needed.
Dry to Recoat
6 hours @ 16°C - 3 Hours @24°C - 1.5 Hours @ 32°C
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Carboline Carbocrylic 3358 IMC

Carboline Carbocrylic 3358 IMC is an intermediate coat on steel or concrete in a three coat system, and can be topcoated with several generic types of topcoats. Excellent abrasion resistance and flexibility with good chemical resistance. Single component Fast drying Low VOC Eggshell finish Coverage Calculator More Information...

In stock

Carboline Carboguard 890

Carboline Carboguard 890 is a self-priming and suitable for application over most existing coatings, and tightly adherent rust. Serves as stand-alone system for a variety of chemical environments and is also designed for various immersion conditions. Excellent chemical resistance Surface tolerant characteristics Conventional and...

Price £79.20
In Stock and Available for Delivery

Carboline Carbomastic 15 LT

Carboline Carbomastic 15 LT is a two-component, high build coating with excellent adhesion to rusted steel and most aged coatings. Surface tolerant Recommended for painting over rusted steel where hand cleaning only is possible Carbomastic 15 LT penetrates through rust to steel substrate and stops further corrosion and undercutting...

Price £74.70
In Stock and Available for Delivery

Carboline Carbozinc 11

Carboline Carbozinc 11 is a two-component, corrosion resistant primer that protects steel galvanically in the harshest environments. Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces Rapid cure. Dry to handle in 45 minutes at 16°C and 50% relative humidity Low temperature cure down to -18°C High zinc...

Price £119.70
In Stock and Available for Delivery

Carboline Carbozinc 859

Carboline Carbozinc 859 is a two-component, low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces Rapid cure. Dry to recoat in 30 minutes at...

In stock

Carboline Carboguard 553

Carboline Carboguard 553 is a two-component, water-based epoxy primer that is easy to apply and has very good chemical resistance. Low odour Very low VOC Fast drying Excellent corrosion protection Very good chemical resistance Contains corrosion inhibitive pigments Coverage Calculator More Information This product is only...

In stock

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery