Bradite One Can Matt

OC63
BRA5773

Bradite One Can Matt is a quick-drying matt finish primer/finish coat in one can, for use as a low odour, quick drying scuff and moisture resistant, adhesion promoting, stain locking, anticorrosive coating for interior or exterior walls and trim, masonry (Brickwork/Concrete etc) ferrous metals, non-ferrous metals, common plastics (e.g. melamine and uPVC), ceramic tiles, glass, wood and existing painted surfaces.

  • Available in 2,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours
  • Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004

Please note: Matt finish products can be more susceptible to scuffs, watermarks, dirt, etc. so in areas of frequent contact/use such as windows, doors, roller shutters etc. an alternative finish may be more suited (such as Bradite One Can Eggshell). Please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for further advice if in doubt.

Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Coverage Calculator

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£21.37
£25.64 Incl. VAT
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Available in 2,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours
  • Quick drying, low odour, cross linking, water thinned primer/finish coat
  • Scuff and moisture resistant
  • Excellent adhesion, stain blocking and anti-corrosive properties
  • Fully anti-corrosive for application to ferrous and non-ferrous metals properly prepared
  • Seals most stains in the primer coat including water, nicotine, hard wood resin bleed, bitumen, asphalt, creosote and many more
  • For interior or exterior walls and trim, masonry (Brickwork/Concrete etc) ferrous metals, non-ferrous metals, common plastics (e.g. melamine and uPVC), ceramic tiles, glass, wood and existing painted surfaces
  • For exterior cladding offering hard wearing, flexible, weather and light resistance, ideal for use over existing cladding coatings (coil, plastisol and powder coatings) with minimal preparation
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Preparation


  • Loose and non adhered contamination should be removed. Cleaning using Bradite TD39 Industrial Degreaser or methylated spirit is recommended to remove oils, grease and other contamination
  • Intact areas of existing coatings should, ideally, be roughened by manual or mechanical sanding. Feather back exposed areas to a sound coating edge. Cracks and pits should be filled using a suitable filler before painting
  • Substrate should be dust free and completely dry before coating

Substrate Preparation

  • Stain locking: Encapsulates stains in the primer coat, application of second coat will be required to hide and in extreme cases a third. One Can should be allowed to hard dry prior to overcoating this will take at least one hour, over application may result in longer drying times
  • Aluminum, stainless steel, galvanised steel, copper and other metals: Cleaned and degreased with methylated spirit, and lightly abraded if possible. White salts on weathered galvanising must be removed during cleaning and degreasing. Light surface rusting can be treated with Bradite Rust Convertor RC46. Heavy rusting to be removed to clean metallic finish (SIS-St 3)
  • New Wood: Ensure moisture content of the timber is below 15% before commencing application. Damp wood should never be painted as this may give rise to blistering, flaking, cracking and premature coating failure. Knots to be wiped using methylated spirit, for heavy or active knots spot prime with Aluminium Wood primer
  • Hard Woods: Wipe with methylated spirit to remove excess resin, changing the face of the cloth regularly. Lightly abrade
  • Green oak: Should not be painted unless it has been weathered for at least 6 months
  • Exterior cladding, Powder coated, Varnish and Existing paint finish: Remove all loose and flaking paintwork. Degrease using Bradite TD39 Industrial Degreaser, followed by clean water rinse. Rub down thoroughly with a medium grade sand paper to provide a key and a defect free smooth surface, “feathering in” areas where paint has been removed
  • UPVC, Formica, Melamine and Plastics: For long term performance, degrease using methylated spirit & lightly abrade surfaces
  • New plaster walls: For plaster skim, allow at least four weeks for the plaster to thoroughly dry. Apply a primer coat by thinning the paint with a 5 to 25% (v/v) addition of clean water, depending upon the porosity of the substrate. Cut in by brushing at the same dilution recommendation as for priming, to promote flow and sealing of the substrate
  • Masonry, brick, concrete: Clean, dry and free of contamination, existing coatings to be sound and well adhered any loose flaking material back to sound well feathered edge, new concrete or masonry to be fully cured. Mould or mildew to be removed and area treated with good quality fungicidal wash following manufacturers instructions



Application


  • Application should always conform with the codes of practice described in BS 6150 and BS 5493
  • Applicable by brush, roller, conventional air spray or airless spray:
    • Brush and Roller - supplied ready for use. Thin with 0-5% Water if required
    • Conventional Air Spraying - Thin with 5-15% water as required. Tip size - 2.0mm. Tip pressure - 60psi (0.4MPa) approximately
    • Airless Spraying - Thin with 0-10% water as required. Tip size - 19 thou (0.48mm) approximately Tip pressure - 2100 psi (15MPa) approximately
  • Apply 2 coats minimum at 40 microns/coat DFT/100 microns/coat WFT
  • Theoretical coverage rate 12 m2/L/coat
  • Touch dry in 30 minutes, recoat in 1 hour, fully cured in 7 days @ 20°C
  • Equipment should be cleaned immediately after use with water



Limitations


  • Matt finish products can be more susceptible to scuffs, watermarks, dirt, etc. so in areas of frequent contact/use such as windows, doors, roller shutters etc. an alternative finish may be more suited (such as Bradite One Can Eggshell)
  • Drying times will be prolonged at lower temperatures
  • For new, fully plastered walls, allow at least six months for the plaster to thoroughly dry before painting. This product is not recommended for painting lime or other natural plasters
  • Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label. In general, avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal protection. Eyes should be copiously washed with water or proprietary wash, and medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and water



Product Details
OC63

Data sheet

For Use By
General Use
For Use On
Wood, Metal, uPVC, Masonry, Glass, Aluminium, Stainless Steel, Galvanised Steel, Copper
Sheen
Matt
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Single
Pack Size
1L, 2.5L, 5L
Application
Brush, Roller, Spray
Coverage
12m2 per Litre
Recommended Thinner/Cleaner
Water
Min. Application Temperature
7°C or above for application (minimum of 3°C above dew point)
Density
1.34 kg/L
Solids by Volume
41.3%
VOC
25 g/l
Shelf Life (from date of manufacture)
2 Years
Touch Dry
30 Mins
Recommended Dry Film Thickness
40 microns/coat
Recommended Wet Film Thickness
100 microns/coat
UN Number
UN3082
Dry to Recoat
1 Hour (Drying times will be prolonged at lower temperatures)
Fully Cured
7 days
Flashpoint
Non-Flammable
Colour(s)
Fully Tintable
Base Type
Water-Based
Exterior / Interior Use
Exterior Use
Type of Wood Finish
Wood Paint
Suitable For
Walls & Ceilings
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

    

You might also like

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £8.02
In Stock and Available for Delivery

Bradite One Can Eggshell

Bradite One Can Eggshell is a quick drying, low odour, water thinned primer/finish coat, with excellent adhesion, stain blocking and anti-corrosive properties. Available in 2,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours Suitable for use over most properly cleaned and prepared commercial uPVC, wood, glass, plastic...

Price £21.37
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28
In Stock and Available for Delivery

Bradite Fastrac Rust Converter

Bradite Fastrac Rust Converter is a high performance, single-pack, water-based rust converter intended for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces. Especially suited for objects which may be difficult to sand blast such as; fences, iron railings, guttering and outdoor...

Price £11.66
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery