Instarmac UltraCrete Flowcon Self-Compacting Concrete is a high specification C40 concrete in a bag, ideal for applications with limited site access where bulk concrete cannot be delivered.
Easily transportable
Flowable
Pre-blended cement for a consistent mix
High compressive strength 55N/mm²
Please note:This product is subject to a minimum order quantity of 2 x pallet layers of 56 x 25kg Bags (112 x 25kg Bags in total)
Flowcon is a high specification, flowable C40 concrete in a bag, ideal for applications with limited site access where bulk concrete cannot be delivered. Flowcon is easily transportable and boasts a high compressive strength of 55N/mm².
Workability: 60 minutes
Set time: 6 hours
Depth: 20mm – 200mm
Pre-blended cement for a consistent quality mix
Applications
UltraCrete Flowcon is a general-purpose flowable concrete, pre-blended and ideal for most multi-purpose concreting applications such as patching or post erection. Flowcon is ideal where a quality mix is required without the waste and inconsistency of site mixed materials.
Technical
Flowcon is supplied in 25kg polythene bags and is manufactured from selected cements, sands, aggregates and chemical admixtures. The product requires only the addition of water and can be applied to depths of 20mm-200mm in one pass. Flowcon should not be used at temperatures below 5°C during application or initial set.
Preparation
Good concrete practice should be observed at all times. All surfaces should be free from oil, grease, dust or any other visible contaminants. Remove all loose particles and work on a sound substrate. Pre-soak the area with clean water prior to application to aid bond. Remove ponded water before applying the product. It is essential that repair edges are saw cut to a minimum depth of 20mm, feather edging is not recommended.
Priming
Remove any dust, dirt or loose debris, the surface area should then be thoroughly soaked with water until saturated. Ensure surplus or ponded water is removed before priming; mix components as per instructions and scrub well into the substrate
Mixing
Each bag of Flowcon contains aggregate as well as a small pack of specialist cements.Add the entire contents of the pack and the aggregate to a standard free fall mixer. If the material is to be mixed by hand, empty contents onto a clean board and mix without adding the water for a short time to combine the cement and the aggregate.
Full preparation, priming and mixing instructions can be found in the product data sheet.
Product Details
4231-781371
Data sheet
Manufacturer
Instarmac
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
25KG Bag
Parts
1 Part
Key Features
Workability: 60 minutes Set time: 6 hours Depth: 20mm – 200mm Pre-blended cement for a consistent quality mix
Coverage
1m² @ 12mm approx
Compressive Strength (at 20°C)
1 day 20.00 3 days 40.00 7 days 50.00 28 days 55.00
Density
2300kg/m³
Shelf Life (from date of manufacture)
Shelf life from date of manufacture in correct conditions for sealed packaging is 8 months
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Instarmac UltraCrete Flowcon Self-Compacting Concrete is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
A fibre modified concrete for backfilling around manhole frames and gullies and can also be used for surface repairs.HAPAS Approved since 2005 Shrinkage compensated Rapid set: 10-20 minutes 20N/mm² compressive Open to traffic: 90 minutes strength after 90 minutesCoverage Calculator
Designed for thick section repairs, haunching reinstatements, ironwork backfilling and commerical sign/post installation.HAPAS Approved since 2005 20N/mm² compressive Rapid set: 10-20 minutes strength in 2 hours Open to traffic: 2 hours • Shrinkage compensatedMore Information Delivery Info
Instarmac UltraCrete QC6 Surface Reinstatement Concrete is a non-shrink concrete designed for the surface reinstatement of ‘picture frames’ or fillets around access covers and surface areas around street furniture.Shrinkage compensated Excellent workability Rapid set: 15 minutes BT Approved Anti-vandal Open to traffic: 4 hours...
Instarmac UltraCrete FTC (Fast Track Concrete) is a fibre modified concrete, suitable for small and large reinstatements to car parks, warehouses and bridge decks.Shrinkage compensated High compressive strength 66N/mm² Foot traffic: 2 hours Pre-blended, just add waterMore Information Delivery Info
For the installation of light duty posts, fences and polesLight duty applications Rapid set: 15 minutes Pre-blended, just add water 25N/mm² compressive strength Please note: This product is subject to a minimum order quantity of 2 x pallet layers of 56 x 25kg bags (112 x 25kg bags in total)More Information Delivery Info
A 10mm concrete formulated for sub-surface use and fast installation of posts, signs, fences, street lighting, speed cameras and road side barriers.Professional grade Easy mix Fast set 41N/mm² compressive strength Two-part mix Please note: This product is subject to a minimum order quantity of 2 x pallet layers of 56 x 25kg Bags (112...