Alternatively you can email our sales & support team on [email protected]
Thermoguard Flame Retardant Topcoat
EGG2.5M
Thermoguard Flame Retardant Topcoat is an oil based, decorative flame-retardant paint used to decorate and complete Thermoguard fire protection upgrading systems.
ADVANTAGES
Oil-based, decorative eggshell or gloss finish with colour options
BS476 Part 7; Class 1 surface spread to flame
BS476 Part 6; Fire propagation
Designated Class 0 in accordance with U.K. Building Regulations
Thermoguard Flame Retardant Topcoat is an oil based, decorative flame retardant paint used to decorate and complete Thermoguard fire protection upgrading systems including:
Thermoguard Flame Retardant Topcoat assists in the control of fire hazards caused by combustible materials such as wood and paint in buildings by releasing a flame extinguishing gas upon contact with fire.
Thermoguard Flame Retardant Topcoat is suitable for use direct as a maintenance coat to bare or sound previously painted non-combustible substrates where the upgrading properties of a Thermoguard basecoats are not required
Finish and Colour Range
Thermoguard Flame Retardant Topcoat is available in a Gloss or Eggshell finish and most RAL and BS colours, please see above and choose from the available selection.
Fire Testing
BS476 Part 7; Class 1 surface spread to flame.
BS476 Part 6; Fire propagation.
Designated Class 0 in accordance with U.K. Building Regulations.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contactedto obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Can I use your paint to coat the existing ceiling plaster work to the cellar steps as this would save fireboarding etc Hope you can help, Many thanks Paul Jepson
Answer:
We wouldn't recommend Thermoguard Flame Retardant Topcoat for plasterboard/plastered surfaces. We can offer an alternative system if you can advise the level of fire protection required - i.e. Class 1, Class 0, 30min, 60min, etc?
Nigel Eustace on 05/05/2016
Question: Can I use your paint products to fireproof my ceiling as I have not used fire retardant plaster board to encase the new steel for my loft extension. I have to have it looked at by a building inspector.
Thanks.
Answer:
You can use our products to achieve BS Class 1, Class 0, 30min or 60min protection on standard plaster walls and ceilings but the product you are currently looking at is not the one to do it. Please contact our Technical Team on 0113 2455450 to discuss your requirements and they will provide a specification and quotation accordingly.
Claire Pullen on 31/01/2016
Question:
What paint should I use to paint an indoor brick fire wall?
Answer:
We recommend using Thermoguard Wallcoat Smoke & Flame Retardant Topcoat. This product isn't heat resistant and may discolour over time if continually subjected to high temperatures, but it is a much safer alternative to standard emulsion.
C raw on 20/09/2015
Question:
Can I use Thermoguard Flame Retardant Eggshell directly onto wood or does it need primer?
Answer:
Thermoguard Flame Retardant Eggshell can be applied directly to wood but if you require any level of fire protection then Thermoguard Timbercoat must be applied first in accordance with it's instructions.
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron:
Up to 90 minutes’ fire resistance
Can be overcoated with compatible decorative topcoat
Water-based
Low odour
Environmentally friendly
Cost effective for large projects
Certificate of supply available on request
Can be applied by brush,...
Thermoguard Timbercoat is a durable fire protection paint for interior and exterior timber surfaces:
Meets new Fire Regulations standard:
BS EN Class B s1 d0, BS Class 1
Class O Surface Spread of Flame
Can also achieve 30 & 60 minutes Fire Resistance in certain instances
Expands to create a barrier, insulating wood from heat and...
Thermoguard Wallcoat is a white intumescent basecoat (part of a complete system) to upgrade potentially dangerous ‘multi-layer’ - previously painted - walls & ceilings in communal areas:
Controls surface spread of flame and fire propagation to Class 0 & EN Class B
Achieves EU and new British safety standards on walls and ceilings...
Nu-Flame FR Gloss is a gloss flame retardant topcoat paint for new and previously painted surfaces where a gloss finish is required. For use on door, skirting and other timber finishes. Tested to BS 476 part 7 and passes Class 1 surface spread of flame.
Advantages
Flame retardant topcoat
Oil-based
Gloss finish
RAL colours
Envirograf HW Premier Top Coat is a coloured, water-based product to apply over Envirograf HW01 White Intumescent Coating with no need for an undercoat:
Available in matt, satin or gloss finishes
For internal use only
Apply one coat at 10 - 12m² per litre
Envirograf HW Superb Top Coat is an innovative, water based, high sheen, coloured gloss, for use over HW01 White Intumescent Coating without the need of an undercoat and also on interior and exterior wood:
Looks, feels and applies like a traditional gloss
Quick drying - reducing application times
Low odour and contains less atmospheric...
Envirograf QVFR Premier Clear Top Coat is a specially formulated, quick drying, water based protective top coating for INTERNAL smooth hardwood and softwood surfaces:
Can be applied by brush, roller or spray
Available in matt, satin or gloss finishes
Can be used over Envirograf QVFR Clear Fire Protection Coating
Low odour
Quick drying...
A flame retardant top coat developed specifically for external walls and is tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations. Perfect for use on external warehouse and industrial outlet walls to minimise potential damage in hazardous environments.
Advantages
RAL shades
Water-soluble...
Thermoguard Smoke & Flame Retardant (SFR) Dualcoat is for use over Thermoguard Timbercoat.
ADVANTAGES
Topcoat and maintenance paint for timber surfaces protected with Thermoguard Timbercoat
Controls surface spread of flames and fire propagation
Total smoke control
BS EN Class B s1 d0 and BS Class 1 and Class 0 (as part of a complete...
Envirograf HW Translucent Top Coat is a spirit based wood stain to apply over Envirograf HW02E Clear Intumescent Coating. Available in a satin finish and suitable for internal or external use.
Envirograf HW Ultimate Clear Top Coat is a specially formulated, quick drying, hard-wearing water based protective top coating for INTERNAL use. It can be applied by brush, roller, or spray and it comes in either a matt or satin finish.
Thermoguard Flame Retardant WB Topcoat, a a quick drying, dual-purpose water-based flame-retardant paint for use over Thermoguard Thermocoat W for 30 or 60 mins Class O fire rating on on-combustible or intumescent protected surfaces.
Protects intumescent paint and helps control the spread of flames
For 30 or 60 mins refer to Thermocoat...
Bollom Flameguard Ultra Vinyl Matt is a top coat for Bollom Broflame Ultra Basecoat on bare and previously painted wood and Bollom Brosteel Ultra 60
Features and Benefits
Hard wearing vinyl matt finish
Top coat for Bollom intumescents for wood and steel
Provides Class 0 on non-combustible surfaces
Peter on 17/09/2018
