International Inter H2O 699 a two-component waterborne acrylic polyurethane finish.
Suitable for use in new construction systems in a wide variety of environments, including commercial infrastructure, factories, processing industries and oil and gas facilities.
| Technial Data | |
|---|---|
| Volume Solids: | 42% ± 3% (depends on colour) |
| Typical Thickness: | 35-45 microns dry equivalent to 83-107 microns wet |
| Theoretical Coverage: | 10.50 m²/litre at 40 microns d.f.t and stated volume solids |
| Practical Coverage: | Allow appropriate loss factors |
| Flash Point: | Part A 101°C Part B 62°C Mixed 101°C |
| VOC: | 61 g/kg |
| Shelf Life: | 12 months minimum at 25°C |
| Drying Information | ||||
|---|---|---|---|---|
| Overcoating Interval with recommended topcoats | ||||
| Temperature | Touch Dry | Hard Dry | Minimum | Maximum |
| 10°C | 4 hours | 16 hours | 16 hours | Extended¹ |
| 15°C | 4 hours | 8 hours | 8 hours | Extended¹ |
| 25°C | 3.5 hours | 6 hours | 6 hours | Extended¹ |
| 40°C | 2 hours | 3 hours | 3 hours | Extended¹ |
Primed Surfaces
Mixing
Material is supplied in two containers as a unit
Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified
Mix Ratio
| Working Pot Life | |||
|---|---|---|---|
| 10°C | 15°C | 25°C | 40°C |
| 2 hours | 2 hours | 2 hours | 1 hour |
| Application Methods | |||
|---|---|---|---|
| Airless Spray: | Recommended | Tip Range 0.33-0.45 mm (13-18 thou) Total output fluid pressure at spray tip not less than 155 kg/cm² (2204 p.s.i.) | |
| Air Spray (Pressure Pot): | Recommended | Gun: DeVilbiss MBC or JGA Air Cap: 704 or 765 Fluid Tip: E | |
| Brush: | Suitable - small areas only | Typically, 30-40 microns (1.2-1.6 mils) can be achieved | |
| Roller: | Suitable - small areas only | Typically, 30-40 microns (1.2-1.6 mils) can be achieved | |
| Thinner: | Not recommended | ||
| Cleaner: | International GTA991 followed by clean potable water | ||
Clean Up
Apply by air or airless spray. Thoroughly flush equipment with International GTA991 thinner, or alcohol, followed by water prior to use. To obtain maximum edge protection and film build, airless or air spray application is recommended. Application by other methods, e.g. brush or roller, may require more than one coat.
Minor areas which are difficult to ventilate should be brush applied to prevent over-application.
Over-application of InterH2O 699 will extend both the minimum overcoating periods and handling times. Over-application will also increase microfoam in the dry film resulting in low gloss.
The following primers/intermediates are recommended for InterH2O 699:
The following topcoats are recommended for InterH2O 699:
For other suitable primers/intermediates consult Rawlins Technical Team on 0113 2455450 (option 2) or [email protected]
Please refer to the product data sheet and safety data sheet in the attachents section above
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
International Inter H2O 699 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
A fast drying reputation isn`t all International Intercure 200HS is renowned for. Complete with MIO, this fast cure anti-corrosive primer/intermediate with added barrier protection, can improve your productivity and lower your solvent emissions.Primer and intermediate in just one coat Rapid recoat times Low temperature cure, cures down...
£578.96 (incl. VAT)
£482.47 (ex. VAT)
International Intercure 420 is a two component, high solids, low VOC epoxy micaceous iron oxide coating formulated on proprietary polymer technology which provides rapid cure and overcoating even under low temperature conditions.Excellent barrier protection as part of a high performance system Suitable for use in aggressive environments...
£363.76 (incl. VAT)
£303.13 (ex. VAT)
International Intergard 475HS is a low VOC, high solids, high build, two component epoxy coating. Available with conventional pigmentation, or alternatively can be pigmented with micaceous iron oxide to provide enhanced overcoating properties.High solids epoxy intermediate Micaceous Iron Oxide variant for additional barrier protection...
£378.20 (incl. VAT)
£315.17 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. International Thinner/Equipment Cleaner GTA991 is used for thinning compatible International products. It can also be used for the general...
International Interthane 990 is a two component acrylic polyurethane finish giving excellent durability and long term recoatability. Across the world, people are experiencing flexible application, extended recoat windows and reduced surface preparation costs with International Interthane 990 in both new construction and as a maintenance...
£130.20 (incl. VAT)
£108.50 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
