Cracking, blistering, flaking and weather resistant
Long lasting finish, excellent colour retention
Anti-fungal degradation - Bonds to glossy paint - Re-coatable in 1 hour
Where application conditions (i.e. winter months) do not allow for water based paint to be used externally, it is recommended to use Zinsser Allcoat Exterior Solvent Based instead
Not suitable for application on floors
Please note: Matt finish products can be more susceptible to scuffs, watermarks, dirt, etc. in areas of frequent contact/use such as windows, doors, roller shutters etc. an alternative finish may be more suited (Satin & Gloss). Please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for further advice if in doubt
Zinsser AllCoat Exterior Matt (Water Based) is an ultimate performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a vapourpermeable, low maintenance water-shedding coating, re-coatable in 1 hour.
ALLCOAT® Exterior Matt contains a biocide to protect the dried coating against fungal degradation.
Designed for all exterior surfaces, ALLCOAT® Exterior Matt is ideal for new or previously painted uPVC, wood, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more. ALLCOAT® Exterior Matt is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT® Exterior Matt will ensure that any exterior looks bright and beautiful for years.
This product is not suitable for application on floors.
Please note: Matt finish products can be more susceptible to scuffs, watermarks, dirt, etc. so in areas of frequent contact/use such as windows, doors, roller shutters etc. an alternative finish may be more suited (such as Satin & Gloss). Please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for further advice if in doubt.
This product is not suitable for application on floors
Product Specification
Technical Data
Zinsser AllCoat Exterior Matt (Water Based)
Finish:
Matt
Tinting:
ALLCOAT® Exterior Matt is available in a full range of BS4800, RAL and NCS colours. Multiple containers of tinted paint should be intermixed (boxed) to ensure colour uniformity
Volume Solids:
40%
Theoretical Coverage Rate:
Up to 12m² per litre on non-porous surfaces
On porous surfaces coverage will be reduced e.g. sawn timber - 4-8m² per litre
Planed timber - 8-12m² per litre
Normal application is 2 coats; however an additional coat should be applied to areas of high exposure such as sills and fascia boards
Typical Film Thickness:
40 microns
VOC Values:
35g/l
Density:
1.25 kg/litre
Limitations:
Not intended for application to exterior floors, decks or any surface subject to water immersion or prolonged contact with water
It is recommended that unweathered / new powder coatings or stoved enamels are to be abraded and degreased thoroughly before applying All Coat Exterior
Not suitable for application onto new plastisol or new powder coating. These surfaces must be fully weathered
Shelf Life:
2 years in unopened containers
Storage:
Store indoors at 5 – 25°C. Protect from frost
Drying Times
Curing Schedule At 20°C and 60% RH
Touch Dry
Dry to Recoat
Hard Dry
Full Cure
1 Hour
1 Hour
4 Hours
7 Days
Drying and recoat times will be extended at lower temperature and higher RH
Surface Preparation
Surfaces should be clean, dry, sound, and free of any contamination that may interfere with adhesion
Remove all loose or peeling paint and chalky paint residue
Sand edges of any remaining paint film until smooth
Special precautions should be taken during surface preparation of pre-1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding
New concrete, masonry and other related surfaces must be cured at least 30 days before priming
Remove all existing mould and mildew before painting. To effectively remove mould and mildew, dirt, and chalky paint residue, use a proper fungicidal wash or exterior house cleaner following the manufacturer’s instructions
Timber at risk from decay or insect attack should be treated with an appropriate preservative
Bare galvanised metal: apply direct to clean, bright metal, no primer required, ensure surface is clean, dry and free from any surface contamination
Bare Ferrous Metal: product contains a flash rust inhibitor so will not rust the bare metal on application, can be applied direct if the metal is completely rust free, if this is unlikely apply a dedicated anti-corrosive metal primer such as Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prior to application of AllCoat Exterior Water Based
Note: AllCoat Exterior Water Based is not anti-corrosive, it acts as a barrier to water reaching the surface and rusting the metal.
Two-Coat System
ALLCOAT® Exterior Matt is self-priming and will adhere to most sound surface. It bonds to existing glossy paints without sanding
The first coat of ALLCOAT® Exterior Matt primes and seals the surface, providing a base for the topcoat. The topcoat completes the sealing process while providing additional moisture resistance and protection
For new or unpainted cedar, redwood, or other resinous timbers prime with Zinsser Cover Stain
Application Methods
Shake or stir well before using
Apply with synthetic bristle brush, roller, or sprayer
For airless spraying, use a .017” tip and high-medium (2000-2500 PSI) pressure
Avoid painting in direct sunlight and maintain a “wet edge” to avoid lapping
Ensure conditions during application and cure are favourable, do not apply if there is a likelihood of rain, frost, fog, or condensation affecting the freshly applied paint before it has fully cured
Application Conditions
Ensure air and surface temperature are between 10°C & 32°C and humidity is less than 85% during application and cure of the product
Health and Safety
Clean Up
Clean application tools, spatters, and spills immediately with warm water and liquid detergent; rinse with water
Follow equipment manufacturer’s directions to clean spray equipment
Remove dried product with a household cleaner, rinse with water
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
This will depend on what substrate is to be painted, if the substrate is previously painted we would recommed testing for compatibiliry and adhesion prior to full application without a primer.
Timber should be primed with Zinsser Cover Stain and for uPVC this can be applied directly once the substrate has been prepared.
Zinsser AllCoat Exterior Matt (Water Based) - Anthracite Grey is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
Zinsser Bulls Eye 1-2-3 Plus is the next generation all surface, all purpose water-based primer, sealer and stainkiller for interior & exterior use. Like Bulls Eye 1-2-3, it deals effortlessly with hard to paint interior and exterior substrates such as glossy surfaces, ceramic tiles, non-ferrous metal, vinyl, hardboard, melamine, varnish,...
Zinsser B-I-N Aerosol is great for priming interior surfaces and spot priming exterior surfaces. It is formulated to seal, prime and block out stains on previously painted or new work and dries in minutes.
• For interior and spot exterior use• Highly effective stain sealer• Seals knots and sap streaks• Permanently blocks odours• Adheres to...
Zinsser Bulls Eye 1-2-3 is a water-based all surface, all-purpose primer, sealer & stainkiller. It is also particularly effective as an adhesion promoting primer for hard-to-stick surfaces even without sanding.
Interior and exterior
Available in 3,000+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
Seals...
Zinsser Cover Stain is an all-surface, all-purpose, oil-based primer, sealer, and stain killer for interior and exterior use
For use on difficult to paint surfaces
Sticks to all surfaces without sanding
Seals water, smoke and nicotine stains
Zinsser’s best exterior wood sealer
Blocks cedar and redwood bleed
Touch dry in 35 minutes...
Zinsser B-I-N is the ultimate performance shellac-based primer-sealer and stain killer for interior and spot exterior use. Offers unparalleled adhesion to glossy surfaces (including glass) without the need for scuff sanding and blocks stubborn and persistent stains.
Ultimate performance primer-sealer
Permanently blocks odours
Unparalleled...
Zinsser Cover Stain Aerosol is an interior / exterior primer, sealer, stain sealer and bond coat that dries for recoat in just two hours.
Features and Benefits:
Ideal for spot work and priming small objects
Interior and exterior
Seals Water, smoke and nicotine stains
Sticks to all surfaces without sanding
Best exterior wood sealer...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
Zinsser Universal Degreaser & Cleaner is a water based detergent that is colour fast, fabric safe and removes tough stains quickly and effectively from many surfaces. A concentrated cleaner, degreaser and stain remover effective against grease and oil and is ideal for cleaning before painting.
Concentrated cleaner, degreaser and stain...
Zinsser Mould Killer and Remover is for use against fungi, moulds and algae on internal surfaces such as tiles, wood, plaster, and wallpaper. Zinsser Mould Killer and Remover is water based and ready for use.
Kills and removes fungi, mould and algae growth
Powerful fast acting formula
Suitable for all interior surfaces
Removes mould...