HMG Cellulose Fluorescent is a high quality fluorescent cellulose product for automotive and industrial use.
HMG Cellulose Fluorescent is part of a three coat system:
| 3 Coat System Details | |||||
|---|---|---|---|---|---|
| Coat 1 | HMG Cellulose APS Primer (White) | ||||
| Coat 2 | HMG Cellulose Fluorescent | ||||
| Coat 3 | HMG Acrythane XSC21 Clear | ||||
HMG Cellulose Fluorescent. A high quality fluorescent cellulose product for automotive and industrial use. To be used as part of a 3 coat system.
HMG Cellulose Fluorescent is part of a three coat system:
| 3 Coat System Details | |||||
|---|---|---|---|---|---|
| Coat 1 | HMG Cellulose APS Primer (White) | ||||
| Coat 2 | HMG Cellulose Fluorescent | ||||
| Coat 3 | HMG Acrythane XSC21 Clear | ||||
Please note more than one coat of each may be required depending on application to achieve desired results.
Additional Infomation
| Technical Data | |
|---|---|
| Volume Solids: | 48.2 % |
| VOC Content: | 0.70kgs/ltr |
| SG: | - |
| Viscosity: | 300 mPas |
| Density: | 1.049 g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
| Shelf Life: | 12 months from delivery date in original sealed containers. |
| Flash Point: | 4°C |
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Compliant Spray: | 20 μm | 50 μm | |
| Pressure Pot: | 20 μm | 50 μm | |
Coverage: 20 square metres per litre @ 20 microns dft (Theoretical)
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 10 minutes |
| Dry To Recoat: | At any stage after flash off. |
| Fully Cured: | 45 minutes |
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
| Technical Data | |||||
|---|---|---|---|---|---|
| Compliant Spray Gun | Pressure Pot | ||||
| Mixing Ratio: | Base: 1 | Base: 1 | |||
| Thinner: 1 | Thinner: 1 | ||||
| Thinner Options: | Thinner 2641 | Thinner 2641 | |||
| Thinner 2642 | Thinner 2642 | ||||
| Viscosity: | 30 - 35 seconds B4 cup | 30 - 35 seconds B4 cup | |||
| Spray Gun Setup: | 1.4 - 1.8 | 1.2 - 1.4 | |||
| Number Of Coats (Guide Only): | 2 - 4 full coats | 2 - 4 full coats | |||
| Flash Off: | 10 minutes | 10 minutes | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Liquid |
| Colour: | Fluorescent Colours |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Change in Condition | |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | 82°C |
| Flash Point: | 4°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 270°C |
| Decomposition temperature: | Not determined. |
| Auto-ignition temperature: | Product is not selfigniting |
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
| Explosion limits: Lower: | 1.1 Vol % |
| Explosion limits: Upper: | 7.1 Vol % |
| Vapour pressure at 20°C: | 29 hPa |
| Density at 20°C: | 1.049 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | 300 mPas |
| Viscosity: Kinematic: | Not determined |
| Solvent content: Organic solvents: | 48.2% |
| Solids content: | 50.4% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Cellulose Fluorescent is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Acrythane 4G Clearcoat (Base) is a high solids acrylic polyurethane coating to meet the stringent requirements of the commercial vehicle market. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane 4G Clearcoat...
£118.62 (incl. VAT)
£98.85 (ex. VAT)
HMG Cellulose APS Primer is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications.Available in grey or white Also available as an aerosol, please see HMG Cellulose APS Primer AerosolMore Information Delivery Info
£23.23 (incl. VAT)
£19.36 (ex. VAT)
HMG Thinner 2641 is a medium fast thinner.Designed for use with cellulose based systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
HMG Thinner 2642 is a medium slow thinner which can be used with compatible HMG systems.For use with cellulose based systems.More Information Delivery Info
£49.86 (incl. VAT)
£41.55 (ex. VAT)
HMG Cellulose Fluorescent Aerosol is a high quality fluorescent cellulose aerosol product for automotive and industrial use. This product is also available in non-aerosol form, please see HMG Cellulose Fluorescent. HMG Cellulose Fluorescent Aerosol is part two of a three coat system:3 Coat System DetailsCoat 1 HMG Cellulose...
£32.54 (incl. VAT)
£27.12 (ex. VAT)
