Limited colours and sizes left in this sale, don't miss out!
- 1 x 5L Blanc Chamrousse 7038
Zinsser AllCoat Exterior Matt (Water Based) is an ultimate performance all surface paint. Designed for the long term decoration (up to 15 years) of timber, metal, masonry, plastic, concrete, cladding and more, it forms a vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour.
- Cracking, blistering and flaking resistant
- Weather resistant
- Long lasting finish
- Easy to apply
- Excellent colour retention
- Multi-surface application
- Anti-fungal degradation
- Bonds to glossy paint
Containing a biocide to protect the dried coating against fungal degradation, it is expertly designed for all exterior surfaces.
Being self-priming, AllCoat Exterior Matt will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of Zinsser AllCoat Exterior Matt (Water Based) will ensure that any exterior looks bright and beautiful for years.
- Painted wood
- Cured concrete
- Weathered bitumen
Zinsser AllCoat Exterior (Water Based) is also available in Satin and Gloss finishes, and in a Solvent Based Satin Finish - ideal for low application in lower temperatures.
Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre-1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting. To effectively remove mould and mildew, dirt and chalky paint residue, use use Zinsser Mould Killer & Remover or an exterior house cleaner following the manufacturer’s instructions. Timber at risk from decay or insect attack should be treated with an appropriate preservative.
2 Coat System
Zinsser AllCoat Exterior Matt (Water Based) is self-priming and will adhere to most sound surfaces. It bonds to existing glossy paints without sanding. The first coat of Zinsser AllCoat Exterior Matt (Water Based) primes and seals the surface, providing a base for the topcoat. The topcoat completes the sealing process while providing additional moisture resistance and protection. Before painting, fill all nail holes and gouges. Where necessary, spot prime knots and sap streaks with Zinsser B-I-N. For new or unpainted cedar, redwood, or other resinous timbers prime with Zinsser Cover Stain.
Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017” tip and high-medium (2000-2500 PSI) pressure. Ensure air and surface temperature are between 10 & 32°C and humidity is less than 85% during application and cure of the product. Avoid painting in direct sunlight and maintain a “wet edge” to avoid lapping. Ensure conditions during application and cure are favourable, do not apply if there is a likelihood of rain, frost, fog or condensation affecting the freshly applied paint before it has fully cured.
At normal temperatures i.e. 20°C and 60% RH, Zinsser AllCoat Exterior Matt (Water Based) dries to recoat in 1 hour and will be hard dry after 4 hours. Full adhesion and hardness develop in 7 days.
Zinsser AllCoat Exterior Matt (Water Based) is available in a full range of BS, RAL and NCS colours. Multiple containers of tinted paint should be intermixed (boxed) to ensure colour uniformity.
Up to 12m² per litre on non-porous surfaces. On porous surfaces coverage will be reduced e.g. sawn timber - 4-8m² per litre. Planed timber - 8-12m² per litre. Normal application is 2 coats, however an additional coat should be applied to areas of high exposure such as sills and fascia boards.
Clean application tools, spatters and spills immediately with warm water and liquid detergent; rinse with water. Dried paint on brushes can be removed with Zinsser B-I-N Brush Cleaner & Restorer. Follow equipment manufacturer’s directions to clean spray equipment. Remove dried product with a household cleaner such as Zinsser Universal Cleaner & Degreaser, rinse with water.
Shelf Life and Storage
2 years from date of manufacture in unopened containers. Store indoors at 5 – 25°C and Protect from frost.
- Not intended for application to exterior floors, decks or any surface subject to water immersion or prolonged contact with water.
- It is recommended that unweathered / new powder coatings or stoved enamels are to be abraded and degreased thoroughly before applying AllCoat Exterior.
- Not suitable for application onto new plastisol or new powder coating - These surfaces must be fully weathered.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.