• RSL Resuseal WB
  • RSL Resuseal WB
  • RSL Resuseal WB

RSL Resuflor WB - Standard Readily Available Colours

SEWBB

Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. 

These standard colours are readily available with faster shipping options; more colours are also available separately that are made to order and have minimum order quantities, with lead times.

  • Low odour, silica Free 
  • Superb adhesion and hard wearing 
  • Hygienic and dust-free

Colour
Size
Finish
£89.08
£106.90 Incl. VAT
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Ordering References


Colour Nearest RAL Match Size Finish Mimimum Order Quantity Delivery Options
Clear - 5 KG Satin 1 Express
Clear - 10 KG Satin 1 Express
Flint Grey RAL 7005 10 KG Satin 1 Express
Stirling Grey RAL 7004 10 KG Satin 1 Express

Products with minimum order quantities may have increased lead times due to being made to order.

Resuflor WB (formerly known as Resuseal WB) provides a curing membrane that hardens a concrete floor. This enhanced hydrating formula is ideal for warehouses, lessening the impact of low to medium traffic forklift trucks and easing the cleaning process. 

Its versatility means that it can be applied to various surfaces, leaving an attractive finish. It is particularly suited to indoor walkways and stairs where cleaning is regularly required, and comes in a satin finish.

RECOMMENDED USES

  • As a seal coat for concrete 
  • Low to medium traffic indoor applications 
  • Food industries and warehouses 
  • Suitable for all types of masonries, asphalt and wood substrates 
  • Indoor walkways and stairs 
  • Automotive workshops

Preparation

Surfaces to be coated must be clean, sound, dry and free of any contaminants that could impair good adhesion.

Substrate temperature should be between 10-30°C with relative air humidity of 70% maximum. Cold, high humidity and lack of air movement can cause a patchy finish, gloss reduction and delay in curing and damage to final properties. To prevent this ensure good drying conditions and air ventilation prevail throughout the application and cure of the product:

New Concrete Floors: New concrete must be clean and sound with surface laitance removed preferably by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required. Open, porous substrates may benefit by applying one extra coat of the specified primer.

Existing Concrete Floors: Remove all dirt, oil, grease, old paints or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and rinse with clean water to make sure all residue of detergents and/or chemicals are completely removed. Local repairs should be carried out prior to main application by using the specified primer, Resuflor WB Clear, then Resupatch.

Priming

Open and porous substrates will require priming. Resuflor WB Clear is recommended and depending on the porosity and texture of the surface to be primed may require two coats. Resuflor WB Clear will not seal block work as it is a thin film primer.  

Application

Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture.

Note: Do not use a separate mixing bucket as it may affect the mixing ratio. 


Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.

Do not add water to this product. Slip resistance can be improved by lightly broadcasting anti slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m sq. When cured, apply the second Resuflor WB coat to secure the aggregates. Alternatively one pack of R.S. Beadgrip can be added to each pack of Resuflor WB to achieve a fine non-slip texture.

Do not apply Resuflor WB on top of polyurethane coatings, as it may not adhere properly. 

Resuflor WB can act as a curing membrane to increase hardness of concrete by allowing full hydration of cement. Resuflor WB can be applied to a new (green) concrete, 7 days after being poured. In such cases expect surface gloss reduction and delay in cure process due to substrate dampness.

Product Details
SEWBB

Data sheet

Manufacturer
RSL
Interior / Exterior Use
Interior
Water / Solvent Based
Water
For Use On
Concrete
Application Method
Roller, Brush, Rake
Sheen
Satin
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5KG, 10KG
Coverage
5kg will cover 40 square metres @ 100 microns wet thickness.
Touch Dry
12-24 Hours
UN Number (Base)
UN3082
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Sean Kendrick on 2021-07-27 18:39:15
Question: 

can resuseal wb be applied to powerfloated concrete?

Answer: 

The concrete must be prepared by grinding or acid etching prior to application as stated in the Technical Data Sheet.

This can be found in the datasheet tab on the product page.


Question about the product

* Required fields
(read)
Send