International Interseal 670HS (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at lower temperatures. The product is still a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating, for application to a wide variety of substrates including hand prepared rusty steel and a wide range of intact, aged coatings.
High solids, low VOC, surface tolerant epoxy
High build - 100-200μm (4-8mils) per coat
Suitable for immersion
Exceptional corrosion resistance
Suitable for application over a range of aged coatings
Can be applied over abrasive blasted, hydroblasted or mechanically cleaned surfaces
Available in a range of colours as well as aluminium
Suitable for application temperatures from -5°C (23°F) to 10°C (50°F)
Compatible with cathodic protection
Certified to ANSI/NSF standard 61
Available in 4,600+ RAL, British Standard and NCS shades, including ready mixed white, grey and aluminium shades
Product customisation
Don't forget to save your customization to be able to add to cart
International Interseal 670HS (Winter Grade) is a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. As a high build epoxy it is suitable for a variety of new construction applications including immersion, as a deck coating or for structural steel. Excellent anti-corrosive protection with minimal surface preparation even when applied over hand prepared rusty steel makes International Interseal 670HS perfect for maintenance too.
Low Temperature Curing
International Interseal 670HS (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at temperatures less than 10°C (50°F), however this curing agent will give an initial shade variation and more rapid discoloration on weathering. International Interseal 670HS (Winter Grade) is capable of curing at temperatures below 0°C (32°F). However, this product should not be applied at temperatures below 0°C (32°F) where there is a possibility of ice formation on the substrate.
Intended Uses
For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings.
Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.
International Interseal 670HS (Winter Grade) is certified to NSF/ANSI Standard 61 (selected colours only). Certification is for tanks greater than 100 gallons (378.5 litres), for pipes which are 6 inches (15cm) in diameter or greater and for valves which are 2 inches (5cm) in diameter or greater.
Features & Benefits
High solids, low VOC, surface tolerant epoxy
High build - 100-200μm (4-8mils) per coat
Suitable for immersion
Exceptional corrosion resistance
Suitable for application over a range of aged coatings
Can be applied over abrasive blasted, hydroblasted or mechanically cleaned surfaces
Available in a range of colours as well as aluminium
Suitable for application temperatures from -5°C (23°F) to 10°C (50°F)
Compatible with cathodic protection
Certified to ANSI/NSF standard 61
International Interseal 670HS has the following specification approvals:
Complies with UK Department of Transport Item No. 116
Complies with UK Department of Transport Item No. 151
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
International Interfine 629HS is a low VOC, high performance, two component, isocyanate free crosslinking acrylic finish which provides good durability in terms of colour and gloss retention.
Designed as a finish coat for use in both new construction and industrial maintenance. For use in a wide variety of aggressive environments including...
International Interfine 878 is a high performance, two component, high solids finish which contains no free isocyanates, offers compliance to current VOC legislation, and affords extended lifetime to first maintenance when utilised as part of a high performance anticorrosive system.
A step change in long term colour and gloss compared to...
International Interfine 979 significantly improves upon the gloss and colour retention exhibited by typical polyurethane finishes also displays the same corrosion resistance and has enhanced mechanical properties when compared to traditional epoxy technology.
Excellent long term color and gloss retention
Contains no free isocyanate
Low...
International Intergard 740 is a two component epoxy finish coat.
Suitable for brush, roller and spray application
Suitable for use in a wide range of environments including offshore structures, petrochemical facilities, bridges, pulp and paper mills, and the power industry
Exclusively available in 4,600+ colours, including RAL, British...
International Thinner/Equipment Cleaner GTA822 is used for thinning compatible International products. It can also be used for the general cleaning of surafces and equipment after using the associated paint or coating.
More Information
International Interthane 870 is high build which means it can reduce the number of coats you require and keep costs to a minimum. Semi-gloss and available in 4,600+ colours (including RAL 9007 Grey Aluminium), International Interthane 870 delivers excellent cosmetics and extended recoatability in both new construction and as an industrial...
International Interthane 990 is a two component acrylic polyurethane finish giving excellent durability and long term recoatability. Across the world, people are experiencing flexible application, extended recoat windows and reduced surface preparation costs with International Interthane 990 in both new construction and as a maintenance...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
