Rust-Oleum 5500 Solvent Free Epoxy is a high build, solvent-free epoxy floor paint for garages, warehouses, showrooms, corridors, indoor car parks, workshops etc. Optimal protection in only one or two layers. High build coating (150 microns), very durable Suitable for frequent (chemical) cleaning Excellent resistance against immersion...
Rust-Oleum 5412 Epoxy Filler
Rust-Oleum 5412 Epoxy Filler is a solvent free, two component epoxy putty for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors.
- Extremely strong: 3x stronger than concrete
- Solvent-free and shrink-free
- Easy 1:1 mixing ratio
- Low odour
- For indoor and outdoor use
Rust-Oleum 5412 Epoxy Filler
Solvent free, two component epoxy putty for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors.
5412 should be used for repair of small cracks, air-pockets and/or blow-holes in concrete walls and floors and is applied with a filling knife or a trowel. Can be applied directly on horizontal and vertical areas. Very porous substrates are to be primed with RUST-OLEUM 5401 Impregnation primer. Can be recoated with 9100, 5500, 9400, Pegakote etc
- Easy to use putty for concrete repair
- Can be applied directly on horizontal and vertical concrete surfaces
- Repair of small cracks, air pockets and/or blow holes
- Low odour
- Prime very porous substrates with the impregnation primer 5401 first
- Density: 1.45
- Solids content in volume: 100 %
- Solids Content in weight: 100 %
- Compressive Strength: 75 MN/m²
- Mixing Ratio: 1 : 1 (Volume)
Drying Times At 20°C/RH 50%
- Touch dry: 4 h (20°C), 8 h (10°C), 3 h (30°C)
- Dry to handle: 16 h (20°C), 36 h (10°C), 12 h (30°C)
- Dry to recoat: 16 h (20°C), 36 h (10°C), 12 h (30°C)
- Fully cured: 7 days (20°C), 14 days (10°C), 5 days (30°C)
- Pot Life: 30 minutes for a 1 kg. mix at 20 °C
1.5 kg/m² per 1 mm thickness.
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Remove oil, grease and all other surface contaminations by alkaline or high pressure (steam) cleaning. Remove loose and unsound concrete until a sound surface is obtained. New concrete or masonry should dry and cure for at least 30 days before applying 5412 or a coating system. The surface should be clean and dry during application.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Dry to Handle (at 20°C)
- 16 Hours
- Dry to Recoat (at 20°C)
- 16 Hours
- Fully Cured (at 20°C)
- 7 Days
- 1m² per litre
- 0 g/l
- Shelf Life (from date of manufacture)
- 2 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
- Touch Dry
- 4 Hours
- UN Number (Activator)
- UN 2735
- UN Number (Base)
- UN 3082
- 1.5 kg/m² per 1 mm thickness.
Be the first to ask a question about this product!
Rust-Oleum Mathys Pegakote is a two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc. It is exceptionally abrasion resistant, very low odour, easy to clean leaving a smooth, stain finish and resistant to oils and solvents. Exceptionally...
Rust-Oleum 9100 High Performance Epoxy is a two-pack, glossy epoxy for metal, walls and floors. It is the most efficient epoxy system providing a very hard coating with high layer thickness giving lasting results with even a single coat application.
Rust-Oleum 5401 Epoxy Impregnation Primer is solvent free and improves adhesion on concrete and other porous, mineral surfaces: Primarily intended for roller and brush application Provides a good key for adhesion on porous, mineral substrates Impregnation of porous and brittle floors Can be applied on slightly damp surfaces Also ideal...
Rust-Oleum 9400 Rust-O-Thane SL is a high build, self-levelling, solvent-free polyurethane that delivers a smooth and seamless finish on interior industrial floors. It should be used on cleaned, horizontal concrete or asphalt floors and is ideal for manufacturing, packaging and warehousing areas. Seamless smooth industrial finish Excellent...
Sika Primer 3N is a universal, one component, solvent primer based on epoxy-polyurethane which should be used on porous substrates prior to the application of Sikabond Adhesives. Features and Benefits: Universal Primer Evaporates quickly Easy to apply
The Sikadur Combiflex SG system is a high performance joint and crack sealing system for construction joints, expansion (movement) joints and connection joints or cracks. The system consists of a modified flexible Polyolefin waterproofing tape, with advanced adhesion properties and a range of different special Sikadur epoxy adhesives for use...
Sikasil WS 355 is a neutral curing silicone sealant with a high movement capability and excellent adhesion to porous and non-porous substrates. Features & Benefits Does not stain areas adjacent to the joint Meets requirements of ISO 11600 25 LM F & G, ASTM C 920 (class 50), ASTM C 1248, TT-S00230C, TT-S001543A Provided with...
Sikasil 670 Fire is a fire rated one part, moisture curing, low modulus elastic joint sealant suitable for movement and connection joints. Features & Benefits Up to 4 hours fire resistance according to EN 1366-4 Outstanding weathering and ageing resistance Movement capability of ±35% (ASTM C 719) Easy to smooth and very good...
SikaFuko Eco 1 is an injectable hose system to seal construction joints in watertight structures against water and salt water ingress. It is cast into the construction joints with the concrete. When it is necessary to seal or reseal the construction joints, it can be injected with the most suitable Sika Injection materials based on acrylic and...
International Interline 921 is a two component, solvent free, chemically resistant epoxy phenolic caulking compound formulated to provide ease of application, and greater flexibility in scheduling of tank lining applications.
SikaSwell A Profiles are acrylic, swellable joint sealing profiles and rings which swell in contact with water. Used to seal construction joints in watertight concrete construction, pipe and steel work penetrations through walls and floor slabs, etc. Features & Benefits Easy to apply Can be applied on different substrates Highly...
Sika Waterbar made from PVC-P can be used as flexible waterstops and are designed for the sealing of movement (expansion) and construction joints in new watertight concrete structures. Sika Waterbar are available in a range of different types, shapes and sizes to suit different types of structures and joint sealing applications. Features...
Sika Concrete Crack Repair is a two part grey epoxy paste, mix in the tube adhesive for high strength repairs to concrete. Can be injected into cracks, can be used on damp concrete, excellent adhesion, economic - only use as much as required, can be applied in vertical and overhead situations, resistant to water, chemicals and solvents....
Remmers IR PUR 250 is a flexible one-component PUR injection resin for sealing of water-bearing cracks and porous, water-soaked areas in concrete and masonry. It is waterproofing, has very good penetration, reacts with moisture: contact with water is necessary for the reaction and hardening of the foam, resistant against damaging soluble...
SikaSeal 140 Multi Purpose Silicone is an acetoxy cure silicone sealant that cures quickly to provide a permanently flexible, high strength waterproof seal. It contains a fungicide to prevent in product mould growth. Features and Benefits Permanently flexible. Anti-fungal formula - prevents mould growth. Quick curing - low dirt pick up....
Sikaflex 521 UV (available as a pack of 12 x 300cc or 20 x 600cc cartridges/sausages) is a one-component PUR-Hybrid sealant based on the Sika Silane Terminated Polymer (STP) technology. The product cures on exposure to atmospheric humidity to form a durable elastomer. Features & Benefits Ageing and weathering resistant Bonds well to...
Sikaflex PRO-3 SL (available in packs of 20x 600cc sausages) is a one part, moisture curing, self levelling elastic joint sealant with high mechanical resistance for indoor and outdoor floors. Applications include; movement and connection joints in floors, pedestrian and traffic areas (e. g. parking decks, car parks), warehouses and...
The Sika Metalsheet FBV joint waterstop is a galvanized metal sheet with a special coating applied on one side to increase its adhesion to fresh concrete. This coating produces a durable watertight bond into the concrete structure during construction. Features & Benefits Tested up to 5 bar hydrostatic water pressure, approved for use...
Sikaflex 252 (pack of 12x300ml cartridges) is a non-sag, 1 component polyurethane adhesive of stiff, paste-like consistency that cures on exposure to atmospheric humidity to form a durable elastomer. It is suitable for use with timber, metals, metal primers and paint coatings (2-c systems), ceramic materials and plastics. Features &...
Sikasil Pool (box of 12x 300ml cartridges) is a one part neutral curing silicone sealant for use in swimming pools and permanently wet areas. It is suitable for joints in and around swimming pools, areas under permanent water immersion and frequently wet areas, such as shower rooms in sports halls or leisure facilities, between ceramics,...