Call 0113 245 5450 for Sales or Technical
Alternatively you can email our sales & support team on [email protected]
Rust-Oleum Mathys Murfill Renovation Paint is a long lasting, elastic and waterproof exterior wall protection paint suitable for a wide range of surface types and is perfectly suited for the renovation and decoration of historical and new buildings. Renovates and embellishes facades, extremely resistant to ageing and contamination, almost no dirt pickup, available in almost any colour.
Rust-Oleum Mathys Murfill Renovation Paint is a matt finish, permanent elastic renovation paint that provides an economical, decorative finish to exterior walls on new construction and historical renovation projects. Rust-Oleum Mathys Murfill Renovation Paint repairs and permanently prevents all hairline cracks. The matt finish also masks any unevenness, new surfaces are highlighted even more beautifully and weathered exterior walls look like new again.
Features & Benefits
Coverage:
Normal consumption: min. 2.5m² per kg (applied over 2 coats).
Coverage is theoretical and depends on many factors such as porosity and roughness of the substrate and material losses during application.
Systems
| Substrate/Condition | Primer/Preparation | Finish |
| Old paints in good condition | Clean and dry | 2 coats of Murfill Renovation |
| Chalking paints | Mathys Fixonal or Mathys Pegafix | 2 coats of Murfill Renovation |
| New or bare substrates | Rust-Oleum Mathys Primer 44 HS, Mathys Fixonal or Mathys Pegafix | 2 coats of Murfill Renovation |
| Smooth and non porous substrates | Rust-Oleum Mathys Pegalink or Rust-Oleum Mathys Noxyde (except for white) diluted with 25% water. | 2 coats of Murfill Waterproofing |
| Cracks < 0.5mm wide | Fill up with Murfill Renovation | 2 coats of Murfill Renovation |
| Cracks > 0.5 mm wide | Fill with Elastofill or Mur-Filler | 2 coats of Murfill Renovation |
| Active cracks | Bridge with Murfill Reinforcement Fleece | 2 coats of Murfill Renovation |
Directions for Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
Surface Preparation
Substrate must be clean, sound and dry (max. 6% substrate humidity) prior to application. Remove any moss, algae, etc. with a suitable detergent.
Application & Thinning
Application Conditions
Minimum temperature: 5°C. Max. 80 % R.H.
Mathys No.1 for Protective Coatings
A facade is the outer face of a building which is subjected to to many internal and external conditions like sun, wind and moisture. The possible causes of degradation are often hard to determine but can include: rising damp, moss, mould, algae and rusting structural reinforcements.
Durable protection and regular maintenance of your facades are of vital importance in preventing problems. Mathys therefore offers an extensive range of paints and coatings that will beautify and protect facades for years to come.
For more than four decades Mathys has been developing effective contemporary solutions for protecting, renovating and decorating facades. Mathys distinguishes itself through its expertise and unparalleled quality and has evolved worldwide into the first port of call for facade protection and decoration.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 David Goold on 31/05/2018 |
Question: I have a sandtex painted brick end of terrace cottage in Lymington. I want to cover the exterior surfaces ( approx 115 sq. m.) with a colored water prof breathable coating via paint brush. Are your products suitable for my application. What approach would you recommend? I can send you photos if needed. Thanks David |
Answer: Rust-Oleum Mathys Murfill Renovation Paint would be an excellent choice, for old paints in good condition, simply clean and dry and apply 2 coats of Rust-Oleum Mathys Murfill Renovation Paint. Based on 115m² you would require 46kg to apply the required 2 coats. | |
| Y Sim on 24/01/2018 |
Question: We have an 8 foot retaining wall in our yard ,recently rough casted ,but we hate it !!.Would we have to have the wall re-rendered before paining, or could the rough cast be coated ? Also ,because the wall is retaining, it always looks & probably is a bit damp.Any advice would be welcome Thank you |
Answer: We would instead recommend Rust-Oleum Mathys Durbocem for this application as it is a problem solving coating for damp walls. The paint is specially formulated to adhere and build a strong bond with the damp surface it is applied to, because it contains cement the moisture on the substrate actually helps the paint cure and become stronger coating. It also allows the surface to breathe so water pressure does not build up behind the coating which in turn prevents any flaking paint or diversion of damp to other areas. | |
| Mogs on 26/09/2016 |
Question: Can this be used directly onto brick? thanks |
Answer: No. Assuming the brick surface to be painted is 'open and porous' (not smooth like engineering brick) it would first need to be primed with Rust-Oleum Mathys Primer 44 HS, Mathys Fixonal or Mathys Pegafix before applying 2 coats of Murfill Renovation Paint in your chosen colour. | |
| Ian Huws on 04/03/2016 |
Question: Can your product be used over K501 treated walls? |
Answer: Sika Liquid Plastics K501 is based on waterbased silane-siloxane technology so Rust-Oleum Mathys Murfill Renovation Paint SHOULD be ok to apply over this type of waterproofer but we would always recommend a sample patch is carried out to ensure compatibility and adhesion. To test, paint about 1m² of Rust-Oleum Mathys Murfill Renovation Paint out onto the surface in an inconspicuous area, allow to fully dry for 3-5 days and then check for any signs of potential issues and test adhesion. | |
| zana mathews on 29/02/2016 |
Question: Can you advise me of its weatherproofing qualities? |
Answer: Rust-Oleum Mathys Murfill Renovation Paint will waterproof the wall but still allow the surface to breathe. It remains permanently elastic and extremely resistant to ageing, contamination and dirt pick up. It is resistant to UV, acid rain, heat, frost and pollution. Any cracks over 0.5mm wide should be filled with Rust-Oleum Mathys Elastofill and any active cracks should be bridged with Rust-Oleum Mathys Murfill Reinforcement Fleece. | |
Keim Concretal C is made using pure inorganic fillers and pigments. The product is solvent free and formulated for use on most concrete surfaces and mineral substrates. Top Advantages Water vapour permeable Colour fast Carbonation protection Solvent free Highly obliterative This product is available as POA. Click here to email us...
Wethertex AP77 Flexible Smooth Masonry Paint is a high performance, exterior quality flexible masonry paint, developed using Optilife silicone technology. ADVANTAGES Advanced 20 year durability Self cleaning Ultra waterproofing Silicone technology Highly breathable Algae resistant Matt finish Excellent adhesion
Nu-Guard® Mural Basecoat provides a solid background colour prior to the application of the Nu-Guard Mural Paint - the water-based paint allowing designers to paint their design onto previously painted concrete and brick. Advantages Perfect basecoat the the Nu-Guard Mural Paint Extensive colour range Touch dry in 1-2 hours. Fully dry in...
An aluminium-filled epoxy for steel and concrete that has excellent resistance to water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Top Features Aluminium flakes provide exceptional barrier...
Plastisol is a common prefinished building material; when grime, grease and dirt collects on it, it looks dirty and old. The Mona-Clean Mastersolve will resolve this problem for you, bringing your building back to life. Also excellent for painted surfaces and hard landscaping surfaces, such as stone or brick. Removes Stains. Soiling....
Keim Soldalit-ME is a highly specialised mineral paint system based on a binding agent combination of silica sol and potassium silicate, for use on exterior surfaces. Top Advantages Highly water repellent High weathering resistance Water vapour permeable, microporous Resists algal and fungal growth This product is available as POA....
Nu-Guard® SP Tack Primer provides smooth, water-soluble primer, prior to the application of the Nu-Guard Mural Paint - the water-based paint allowing designers to paint their design onto previously painted concrete and brick. Advantages Smooth finish Water-soluble Non-toxic 12-month shelf life
Nu-Guard® Tack Primer gives you the base coat on which to apply the Nu-Guard AG System to non-porous or existing coatings. Advantages Exceptional adhesion to non-porous surfaces. Primer coat for the Nu-Guard AG System. Touch Dry from 3-4 hours. Water soluble. 12-month Shelf life.
Remmers Primer SV Primer SV is a solvent based and alkali resistant agent with high penetration capacity and a strengthening and hydrophobizing effect. Used as a strengthening primer for sanding, mineral building material substrates and weathered fibrated cement sheets beneath Silicone Resin Paint LA, Silicone Resin Filler Paint LA, Concrete...
SL1 Shadow Lifter is the ideal solution for those looking to get rid of stubborn graffiti shadows. For example, when applying graffiti removal from the brickwork, a shadow of the graffiti may remain. The SL1 Shadow Lifter has been formulated to cure this problem. Advantages Removes graffiti shadow Removes general soiling Perfect for...
Keim Stone Cleaner (also known as Steinreiniger N) is a neutral, environmentally friendly, biodegradable cleaner for stone. Suitable for mild and gentle cleaning of well-adhered dust, grease, oil and soot pollution on natural stone, concrete and render facades. Top Advantages Appearance: Transparent liquid Density: 1.0 g/cm3 pH value:...
Wethertex WeatherBLOCKER is the perfect one stop solution for protecting your building from the damaging effects of penetrating damp. Developed using nano-technology, this clear, waterproof coating penetrates deep into brick or stone to give up to 25 years protection against damp without affecting the appearance of the substrate....
Remmers Quartz Primer is a bonding layer for cementitious substrates with low absorption behaviour. Remmers Quartz Primer is suitable for all cementitious substrates that have low absorption capacity because of low porosity. With Remmers Quartz Primer, a bonding layer is produced between the "render-unfriendly" substrate and the render to be applied....
Thermilate PRO Insulating S-Flex Coating is a smooth high build, flexible, insulating and waterproofing wall coating for exterior walls. It provides maximum strength protection and flexibility while remaining breathable to prevent mould growth. Saves energy, saves money.
Sikagard 670 W ElastoColor is an acrylic, anti-carbonation protective coating for exposed concrete. ADVANTAGES Water vapour permeable Very good resistance against weathering and ageing Easy application Environmentally friendly (solvent free) Prevents water ingress High diffusion resistance to CO2
Remmers Funcosil MCI is a one component water based corrosion inhibiting impregnation for preventative maintenance of all reinforced concrete buildings & structures. Used for civil engineering structures including bridges, piers, car parks, cooling towers & marine concrete structures. Image already added
